Rockford Fosgate Stage 3 Audio Upgrade Kit for Select 2016-17 Yamaha YXZ Models (YXZSTAGE3)

Digital Media Receiver & Installation Kit

YXZ Dash Kit: The included RFYXZ-PMXDK dash kit is designed to facilitate the addition of the Rockford Fosgate PMX-2 digital marine source unit into select Yamaha YXZ model ATVs. The dash kit includes a main dash bezel and mounting hardware, plus a radio housing and wiring harness. The RFYXZ-PMXDK dash kit is specifically designed for 2016-up Yamaha YXZ model ATVs. The dash kit mounts to the factory storage pocket. Its texture and color matches factory dash & interior.

Notes:

• Requires drilling a 2" access hole in center pocket.
• The included harness of RFYXZ-PMXDK dash kit for the PMX-2 is designed to plug directly into Yamaha YXZ series factory wiring harness.
• The included harness and trim-bezel for the PMX-0 will not be used.

Marine Receiver: Rockford Fosgate's PMX series of source units are fully tested against UV radiation degradation as well as tested to IPX water intrusion standards. They are also fully tested for ever changing environmental conditions such as temperature extremes, as well as vibration testing to make sure they can take a bump and keep performing. The PMX-2 is protected against Dust, UV, Temperature, Water, Corrosion & Vibration.

• Dust: The unit's display and motor structure are sealed up tight so they look as clear as possible and perform day in and day out no matter how many times you hit the trails.
• UV Inhibitor Materials: Centrex and ASA plastic materials are used for UV radiation resistance and components are tested in accordance with ASTM D4329 testing and certification procedures.
• Thermal Shock Tested: Tested for extreme temperature operation as well as severe fluctuations in ambient temperature. Components are taken to both low and high temperature extremes and then tested to ensure operational capabilities.
• Water Tested: IPX5 and IPX6 Ratings allow for the components to be directly sprayed with water without water incursion.
• Corrosion Protection: Two part epoxy coated PCB boards prevent corrosion of critical components due to exposure in moisture rich environments.
• Vibration: Subjected to full vibration and shock testing to ensure that it will take abuse and keep performing to our stringent standards.

Optically Bonded LCD & Water Resistant Control Knob: The Rockford Fosgate PMX-2 features a 2.7" TFT color LCD for optimum viewing, even in full sun, that is optically wet bonded to prevent any dust or moisture penetration. There are two brightness settings for the LCD screen. The PMX-2 uses a water resistant rotary encoder knob, along with push-button controls that feature white LED illumination.

Voltage Gauge/Warning & EEPROM: You can check the voltage of your system through the PMX-2's menu. The unit also provides a Low Voltage Warning Alert. The Rockford Fosgate PMX-2 features an EEPROM (Electrically Erasable Programmable Read-Only Memory) which retains settings even when power is removed.

Bluetooth Music Streaming: The Rockford Fosgate PMX-2 offers built-in Bluetooth (version 3.0+EDR) for wireless music playback from your Bluetooth-enabled Apple iPod/iPhone/iPad, Android smartphone/tablet, Windows phone, Blackberry, and more. You are able to stream stored music and music apps from your Bluetooth device to the PMX-2 marine receiver. You can control basic playback functions like Play/Pause, Previous Next/Track and Repeat/Shuffle for stored music and music apps on your device. When using a Bluetooth AVRCP 1.4 compatible device like the Apple iPhone (iOS 5.0+) or an Android smartphone (OS 4.0+), you can even browse your stored music by category (Playlist/Artist/Song/Genre). The PMX-2 will also display your device's song/artist information with album art.

Note: This unit does not support Bluetooth hands-free communication for phone calls.

Optional Wired Remotes: The PMX-2 features a wired remote input which is compatible with Rockford Fosgate's PMX-1R & PMX-0R wired remote controllers (both sold separately). In most cases you will need one of Rockford Fosgate's extension cables (sold separately) to connect a wired remote controller. Up to 3 remotes can be added to one marine receiver using PMXYC Y-cable (sold separately).

USB Port: The Rockford Fosgate PMX-2 features a rear-panel USB (type-A) port for connection of a USB mass storage class device, like a USB thumbdrive or flashdrive. The unit supports playback of MP3 music files loaded onto a USB MSC device. You are able to browse your music by folders, as well as control basic playback functions like Play/Pause, Previous/Next Track and Repeat/Random.

iPod/iPhone Direct Connection: The Rockford Fosgate PMX-2's USB port can be used to connect your Lightning-connector or 30-pin dock connector iPod/iPhone to the head unit. Simply use the cable that came with your iPod/iPhone device or a 3rd party Apple certified cable (sold separately). The PMX-2 supports audio playback, music navigation, information display (including album art), and charging of your compatible Apple device.

• Music Control: The PMX-2 lets you navigate your Apple device's stored music by Playlist, Artist, Album, Song, Genre, Podcast, Composer, or Audiobook. The head unit also offers basic playback functions like Play/Pause, Previous/Next Track, and Random/Repeat. Newer Apple devices with iOS 6.0+ will remain unlocked while connected, so you can access music apps on your device. Older Apple device's will lock when connected to the PMX-2.
• Song/Artist Info + Album Art: The head unit will display your iPod/iPhone's stored music file information; including Track number, Elapsed playing time, Song title, and Artist/Artist name. It will also display album art.
• Charging: The head unit's USB connection provides 1A of current to power and charge your connected iPod/iPhone when your vehicle's ignition switch is set to the 'ACC' or 'On' position (if your iPod/iPhone has no initial battery charge, then the unit will not recognize it).

Pandora Internet Radio: The free Pandora App (either from Apple's App Store or Google Play) lets you play music from the Pandora music service through the Rockford Fosgate PMX-2 using your USB-connected or Bluetooth-paired Apple iPhone (iOS 9.0+), or Bluetooth-paired Android smartphone. Your Apple iPhone must be connected to the PMX-2 via the appropriate the Dock-/Lightning-cable that came with your iPhone or via Bluetooth. Your Android smartphone must support A2DP/AVRCP/SPP Bluetooth profiles and be paired with the marine receiver. Your iPhone or Android smartphone will also need an active Data Plan account with connection to the Internet via 3G, EDGE, or WiFi. The PMX-2 provides control over the Pandora music service and displays Artist, Album, and Song information.

• Station List: You can select Pandora stations from your Station List by date or alphabetically.
• New Station: Based on a currently playing track or artist, you can create a new station and save it to your Pandora account.
• Skip Songs: You can skip song tracks within a station. You cannot skip back to a previous song. Pandora limits the number of skips allowed.
• Thumbs Up/Down: You can give songs a thumbs up or thumbs down to help Pandora personalize stations to suit your preferences.
• Bookmarking: The song or artist currently being played can be bookmarked & stored in your Pandora account.

Aux Input: The Rockford Fosgate PMX-2 is fitted with a rear-panel stereo RCA AUX input to connect an external audio source. You can give the Aux input a custom name.

AM/FM Tuner: The PMX-2 features a built-in AM/FM tuner with manual, seek, and preset tuning. You can store up to 18 FM and 12 AM preset stations; these presets can be stored manually or automatically. You can set the tuner to Local or Distance tuning. The Local option tunes to nearby radio stations with sufficiently strong signals for good reception. In areas where reception is poor, switching to Distance tuning enables the unit to tune in to more distant stations. You can choose between US or European tuning.

Weather Band: The Rockford Fosgate PMX-2 is also equipped with a built-in weather band tuner. Select from weather band frequencies between 162.40 to 162.55.

MOSFET Amplifier: The PMX-2 is equipped with a MOSFET amplifier. Compared to conventional power supplies, the MOSFET amplification circuit is smaller and more efficient, and it delivers increased power with less distortion and absolutely zero on/off switching noise. More power means louder and cleaner music at higher volumes because you're not pushing the limits of the amplification circuit.

• Full Bandwidth Power: 25 watts RMS x 4 channels (at 4 ohms, 20-20kHz, 1% THD)
• Maximum Output Power: 50 watts x 4 channels (200 watts total)

Note: The power specifications for the marine receiver are compliant with the CEA2006 Mobile Amplifier Power Testing and Measurement standards from the Consumer Electronics Association (CEA). These standards were developed as a way to equitably compare power specs from model to model and between manufacturers.

4V/4Ch Preouts: The Rockford Fosgate PMX-2 is equipped with two pair of 4-volt preamp outputs (Front & Rear/Sub). You can configure the Rear/Sub pre-out for rear speakers with fading capability or as a non-fading sub output. You can turn off the unit's internal amplifier, you plan on using only external amps.

Equalizer: The PMX-2 is equipped with a variety of EQ presets, and 7-Band EQ, and Rockford Fosgate's Punch EQ.

• Presets: Select between seven EQ presets - FLAT, ROCK, CLASSIC, ACOUSTIC, DANCE, ELECTRONIC, or HIP-HOP.
• 7-Band EQ: Use the built-in 7-band EQ to custom tailor the sound of your music to your liking.
• Punch EQ: Punch EQ is an onboard equalizer with up to +18dB at 45Hz and/or up to +12dB boost at 12.5kHz.

High-Pass & Low-Pass Crossovers: The PMX-2 provides a high-pass crossover for the front & rear channels which can be set to 60Hz, 80Hz, 120Hz, or Full-Range. The unit also provides a low-pass crossover for the subwoofer output that can be set to 60Hz, 80Hz, 120Hz, or Full-Range.

Sub Control: When the sub out is activated, you can independently adjust its volume level from 0 to 40.

Source Gain: You can adjust the gain of each source so they all play at the same volume level. Select between -3dB, -2dB, -1dB, 0dB, +1dB, +2dB, or +3dB for each source.

Key Beep: A beep tone will sound with any press of a button on the receiver. This can be turned on or off.

Amplifier & Amp Wire Kit

4-Channel Amplifier: The Rockford Fosgate Power T400X4ad is an ultra-compact four-channel amplifier. Even though the amplifier is only 8-5/8" x 4-1/4", it puts out a full 100 watts per channel at 4 ohms or 2 ohms. In bridged mono, the output is 400 watts at 4 ohms.

Class AD: The amplifier features Rockford Fosgate's proprietary Class AD technology, which allows the amp to produce more power with less current draw. It takes the highly efficient bd amplifier design to a full-range application. Class AD uses Dynamic Frequency Switching to increase the switching frequency during lower output levels for better signal resolution. In addition, Post Choke Feedback Filtering removes unwanted distortion by comparing the input signal to the output signal at the speaker connector.

Constant Power: Rockford Fosgate uses a patented circuit design to gain up to 25% more output power. Constant Power actively increases the voltage and current in direct relationship to the rise and fall of music signals to provide additional power.

Fan Cooled: The T400X4ad features dual fans to keep the amp running cool. Dual Fan Forced Induction pulls in fresh air, which pulls heat off of the MOSFETs, and directs airflow into the exhaust channel and out of the amplifier. Since the top and bottom heat sinks are decoupled, the top remains cool to the touch. When installing, you should leave at least 2-3" of clearance around the ends of the amplifier to optimize air flow to the fan intake and exhaust vents.

C.L.E.A.N. Technology: Using Rockford's C.L.E.A.N. (Calibrated Level Eliminates Audible Noise) technology, you can easily and precisely set up the amplifier levels to eliminate distortion from damaging your speakers. Simple LED indicators are used, instead of test equipment, to identify signal clipping at both the input and output, and to match the audio source to the amplifier.

Top Mounted Controls: The T400X4ad features easy-to-reach controls on the top panel of the amplifier. There are two sets of controls: one for the front channels and another for the rear channels. The controls include:

• 2/4 Channel Switch: This switch determines which inputs are active. In the 2CH position, only the front inputs are active, allowing you to feed the signal to all four channels with only a two-channel input. In the 4CH position, both the front and rear inputs are active.
• Input Level: This rotary control lets you match the output of the audio source to the amplifier. A small screwdriver (not included) is required to set the levels.
• Punch EQ: The Gyrator-based Punch EQ eliminates frequency shift with boost. It works in conjunction with the crossover switch on the amplifier. When set to Low-Pass operation, it functions as a 0 to +18dB variable Bass Boost at 45Hz. When set to High-Pass, it is a 0 to +14dB variable Mid-Bass and Treble Boost at 12.5kHz. When set to All-Pass, the Punch EQ boosts both the bass and treble frequencies. A small screwdriver (not included) is required to set the amount of boost desired.
• Crossover Switch: This 3-way switch lets you select Low-Pass (LP), High-Pass (HP), or All-Pass (AP) on the Butterworth crossover.
• Frequency: The crossover frequency is constantly variable between 50Hz and 250Hz with a slope of 12dB/octave. A small screwdriver (not included) is required to set the crossover cut-off frequency.

LED Indicators: The amplifier has three LED indicators on its top panel:

• Input Clip Indicator: The input clip indicator works in conjunction with the audio source's volume knob. It will illuminate red when the audio source reaches its clipping point.
• Output Clip Indicator: The output clip indicator works in conjunction with the amplifier's input level knob. It will illuminate red when the output level has reached the clipping point. When setting the level using test tones, you should adjust the output level until the LED glows blue. If setting the output level using music, the LED should glow blue with only an occasional red indication.
• Power/Protect: The Power LED illuminates blue when the unit is turned on. If the LED turns yellow, a short circuit or too low of an impedance has been detected at the speaker connections. If the LED turns red, the amp has overheated and has shut down.

Speakers & Subwoofer

Marine Rated Speakers: The Rockford Fosgate RM1652 marine rated speakers utilize 1" dome tweeters that are made of LCP (liquid crystal polymer), a high strength/light weight material, die cast into a volcano design. The tweeters are bridge mounted, useful in a marine speaker because no opening through the middle of the woofer for the mounting post is needed. The woofer cones are injection molded, mineral filled polypropylene with UV inhibitors. This molding process assures a uniform cone thickness for superior linearity and clarity. It is also light weight and rigid for decreased distortion and improved bass response.

• ICC Crossover: The ICC (Integrated Concealed Crossover) simplifies installation and protects the crossover by concealing it inside the basket, creating a cleaner look and easier installation. The crossover is 6 dB/octave high pass.
• Infinite-Baffle Operation: The speakers are designed for infinite-baffle operation and can be installed in a variety of locations, without the need for a dedicated enclosure.
• VAST Surround: The Vertical Attach Surround Technique (VAST) increases a speaker's effective radiating cone area without increasing the size of the basket.
• Klippel Verified: The Klippel distortion analyzer, a device that uses a laser and sophisticated software to do large-scale analysis of drivers in motion, lets Rockford Fosgate optimize the speaker's motor structure, voice coil alignment, and suspension to yield the best possible performance.

Note: Rockford Fosgate uses industry standard tests (ASTM B117 salt/fog and ASTM D4329 sunlight, moisture, and heat) to ensure the RM1652 speakers will provide optimum performance in the difficult marine environment. The mounting hardware is stainless steel to resist corrosion.

Front Lower Speaker Enclosure: The two compression molded fiberglass reinforced polymer speaker enclosures with UV resistant finish are optimized for the two included Rockford Fosgate RM1652 Marine speaker and mount perfectly in a compatible Yamaha YXZ model ATV. They are designed to match the Yamaha YXZ ATV's texture and color, plus mount in factory locations with minimal disassembly and drilling. Two speaker harnesses connect between the RM1652 speakers and the included Amp wire kit's harness which plugs directly into the T400X4ad amplifier.

Marine 10" Dual 2-Ohm Woofer:The RM110D2B is a black 10", dual 2-ohm Prime R1 subwoofer rated at 200W RMS/400W Peak that has been designed for marine watercraft or powersports applications. It features color matched grille and is UV and moisture resistant. The woofer is fitted with spring-post speaker terminals.

• VAST Surround: Rockford Fosgate's proprietary surround technique, VAST, provides up to a 25% increase in the speakers effective radiating cone area without complicated installation issues. This design alters the typical design and manufacturing technique by eliminating the large flat glue surface area (the landing), which allows the surround to be shifted for increased cone area. In turn, both nominal efficiency and maximum output capabilities are dramatically improved.
• Anodized Aluminum Voice Coil Former: Rockford Fosgate subwoofer uses an anodized aluminum voice coil former for superior heat dissipation (up to 100° at full power levels). Unlike traditional plastic substitutions, aluminum acts like a heat-sink to quickly dissipate thermal build-up on the voice coil. This keeps subwoofers cool during high SPL conditions.
• Klippel Verified: The Klippel distortion analyzer, a device that uses a laser and sophisticated software to do large-scale analysis of drivers in motion, lets Rockford Fosgate optimize the speaker's motor structure, voice coil alignment, and suspension to yield the best possible performance.

Subwoofer Enclosure: The compression molded fiberglass reinforced polymer subwoofer enclosure with UV resistant finish is optimized for the included Rockford Fosgate RM110D2B 10" woofer and mounts perfectly in a compatible Yamaha YXZ model ATV. The enclosure is designed to match the Yamaha YXZ ATV's texture and color, plus mount in factory locations with minimal disassembly, modification, and drilling. The enclosure bolts in directly to factory mounting holes and offers a stealth install once mounted and body panels are replaced. A subwoofer harness connects between the RM110D2B 10" woofer and the included Amp wire kit's harness which plugs directly into the T400X4ad amplifier.

Marine Tested: Rockford Fosgate uses industry standard tests (ASTM B117 salt/fog and ASTM D4329 sunlight, moisture, and heat) to ensure theses speakers will provide optimum performance in the difficult marine environment.

• ASTM B117 salt/fog test standard provides accelerated aging in a controlled corrosive environment to produce relative corrosion resistance information for specimens of metals and coated metals.
• ASTM D4329 test standard is intended to induce property changes associated with end-use conditions, including the effects of sunlight, moisture, and heat.