WET SOUNDS SINISTER SERIES 6-channel CLASS D AMPLIFER (SD6)
The Wet Sounds Sinister SD6 marine amp packs an astounding amount of punch into a compact chassis, delivering 185 watts RMS per channel at 4 ohms, or an impressive 585 watts when you bridge two channels together. This Class D 6-channel amplifier combines with a Wet Sounds MAXED™ power supply to provide efficiency levels rarely seen in any mobile amps, much less marine models.
Earn 3194 VIP POINTS!
A high-performance amp for your boat
Designed by boaters for boaters, Wet Sounds Sinister Series™ amps give you serious sound while enduring the toughest parts of life on the water. A conformal-coated PCB circuit board, a sealed, salt-water resistant heat sink, and stainless steel hardware ensure that this amp will stand up to salt, spray, high temperatures, and high volume levels.
Big-time power and efficiency
The Wet Sounds Sinister SD6 marine amp packs an astounding amount of punch into a compact chassis, delivering 185 watts RMS per channel at 4 ohms, or an impressive 585 watts when you bridge two channels together. This Class D 6-channel amplifier combines with a Wet Sounds MAXED™ power supply to provide efficiency levels rarely seen in any mobile amps, much less marine models. You can configure this amp to run almost any speaker setup — from multiple speakers and tower systems to high-performance marine subwoofers.
With a bass boost and high- and low-pass filters on all six channels, you'll be able to fine-tune your audio system to get the sound you want. The power, speaker, and input sections are conveniently located on one side of the amp, while the top-mounted controls are protected by a removable cover.
Other features on the SD6 include flexible source selection for single or multiple RCA channel input, RCA pass-through in 4-channel and 2-channel modes, and removable speaker plugs that accept heavy-gauge wire. The SD6 also sports built-in microprocessors that monitor voltage levels, temperature, and much more to protect your amp from damage, no matter how long the party lasts.
Get the look you like
Because every boat installation (not to mention every boater) is unique, this marine amp lets you create a great-sounding system that suits your boat — and your style. Removable power/ground and speaker wire plugs are a big help if you install your amp in a tight location, while built-in mounting feet allow you to run wiring under the amp so a more exposed installation will still look clean and neat. The sleek black exterior is accented by Wet Sounds logos backlit in your choice of red, white or blue. You can even mount the logos horizontally or vertically to suit your installation.
- full-range 6-channel marine amplifier
- 585 watts RMS x 3 at 4 ohms in bridged mode
- 185 watts RMS x 6 at 4 ohms (290 watts RMS x 6 at 2 ohms)
- Class-D design
- Wet Sounds MAXED power supply (patent pending)
- advanced microprocessor control
- conformal-coated PCB circuit board
- saltwater-resistant heat sink
- rugged water-resistant design
- stainless steel hardware
- top-mounted controls with protective cover
- removable speaker plugs
- variable low-pass and high-pass filters
- variable bass boost: 0-12.5 dB at 27-110 Hz
- frequency response: 3-35,000 Hz
- dimensions: 13-1/2"W x 9-3/4"D x 2-11/16"H
- warranty: 1 year
|RMS Power Output (Watts x Channels)|
|Frequency Response at Rated RMS Power||---|
|THD at Rated RMS Power||---|
|Signal to Noise Ratio||---|
|Peak Power Output (Watts x Channels)||---|
|Power at 2 Ohms (Watts x Channels)||---|
|Bridged Power (Watts x Channels)||---|
|Minimum Impedance Bridged||---|
|Minimum Impedance Unbridged||---|
|Low-Pass Crossover Frequency||---|
|Low-Pass Slope (dB/octave)||---|
|High-Pass Crossover Frequency||---|
|High-Pass Slope (dB/octave)||---|
|Bass Boost Frequency||27-110|
|Speaker Level Inputs||---|
|Parts Warranty||1 year|
|Labor Warranty||1 year|